| IMPERIAL®
specialty wrenches and service kits |
|
| Wrenches
and Service kits for Refrigeration and Air-Conditioning Service. |
|
|
123-C
|
124-C
|
127-C
|
127-CO
|
•
Rugged
steel forged wrench.
•
For
use on small refrigerant cylinders,
shut-off valves, packing gland nuts, etc.
•
Ratchet
has 1/4" square drive and raised face.
•
Handle
has 3/16" and 1/4" square drives and 1/2" ex.
|
•
Combination
wrench with the four sizes most needed for servicing air-conditioning
and refrigerator equipment.
• 9/16" hex for dust cap on access valves and plug oil check on
compressor.
• 1/2" hex for compressor mounting bolts.
• 1/4" square for valve stem and service valves and old style
compressor valves.
• 3/16" square for valve refrigerant charging tanks.
|
•
Compressor
access valve wrench.
•
Has
1/4", 3/8", 3/16" and 5/16" square drive ratchets
• Specially
designed for use on compressors with access valves in hard to reach
places.
•
Reversible
ratchets.
|
•
Compressor
access valve wrench.
•
Has
1/4", 3/8", 3/16" and 5/16" square drive ratchets
• Specially
designed for use on compressors with access valves in hard to reach
places.
•
Reversible
ratchets.
•
Same
as 127-C except with unique 25° offset that provides additional
convenience in hard to reach places.
• Wt.
1.5 lbs.
|
|
 Kwik-Charge®
|
 Kwik-Coupler®
|
Tube
Reamer 208-F
For 3/16" to 1-1/2" O.D. tubing
|
Pinch
Off Tool 105-FF
For 1/4", 5/16", 3/8" and 1/2" O.D. tubing
|
•
Liquid
low side charger provides fast, safe charge essential when using
tracing dye.
•
Kwik-Charge
accepts liquid refrigerant from the cylinder and discharges into low
side of the system. Charging rate is up to eight times faster than
vapor charging. In addition, liquid charging is required when using
R-410A and other blended refrigerants.
•
Kwik-Charge
is attached to the low side of the charging manifold.
Features:-
• Up to 8 times faster than vapor charging.
• No need to heat refrigerant cylinder.
• Built-in check valve opens for drawing unrestricted vacuum.
• No pressure drop in cylinder.
• One charger services all units 1/2 ton or larger.
• 535-C Kwik-Charge 1/4" female SAE flare inlet, 1/4" male SAE flare
outlet.
|
•
The
Kwik-Coupler® set is intended
for use with refrigeration and
air-conditioning service hoses when
connecting to core valve type access
fittings.
•
Conventional
threaded connecting
is converted to push-pull operation
which is faster, easier and positive
sealing at all times.
•
Valve
cores are depressed
automatically without adjustments
or loss of refrigerant. Disconnecting
is also accomplished without loss
of refrigerant.
•
16-C
Straight Coupler (45° Flare)
1/4" female x 1/4" male.
•
17-C
90° Elbow Coupler (45° Flare)
1/4" female x 1/4" male.
|
•
Reams
both inside and outside edges of tube with 3 hollow ground cutters.
•
Tough
die cast body. Deburrs both clockwise and counterclockwise. Fluted body
is shaped to fit comfortably in palm.
•
Reamer
for copper, aluminum and brass tubing.
•
Hardened
steel cutter blades.
•
Wt.
.63 lbs.
|
•
Temporarily
closes soft copper, aluminum or steel tubing so no liquid or gas passes
sealed part.
•
Lets
you disconnect Iine while making repairs without loss of liquid or gas.
Also opens tubing to allow flow.
•
Wt. .75 lbs.
|
|
This Category is currently empty
|
|
|
